Employment

Aeroforce S2S Safety (Grain)

Important Safety Information

OPERATION  |  Safety Messages


Read entire sheet before operating this product.

Routinely inspect tarp and swing arms for broken or damaged parts.

  • DO NOT operate with repaired arms/castings. Repaired arms/castings could fail.
  • DO NOT operate if parts are broken or damaged. Broken or damaged parts may come loose unexpectedly and allow the arm to rotate with tremendous force. Secure parts and have repairs made IMMEDIATELY.
  • DO NOT operate if the swing arms fail to rotate freely under normal operation for any reason. Discontinue use until repairs or replacements can be made.
DO NOT operate when damaged.





Spring and arms are under extreme tension.
DO NOT stand in the path of damaged or broken or swing arms or tarp. They could come loose causing serious injury.

DO NOT unlock the clamps holding the anchor pipe before releasing the spring tension on the AeroForce S2S. Unlocking the anchor pipe clamps can cause a rapid release of spring tension allowing arms to rotate with the anchor pipe and tarp coming off the trailer. Persons in the area could be hit with moving parts.

DO NOT unlock the roll stops holding the anchor pipe.





Keep all clothing clear of moving parts

Swing arms rotate under extreme spring tension.
DO NOT operate while anyone is standing in the path of the arms.
DO NOT stand in the path of the front/rear swing arms or injury could occur.

Tarp MUST be fully covered or fully uncovered before driving. If not properly positioned. (covered or uncovered) damage could occur from overhead obstructions.

Tarp MUST be fully covered or fully uncovered before driving.




Electric Operation Instructions

NOT releasing the switch when the covered or uncovered position is reached may cause the motor to burn out.

SWITCH
Direction switch operates depending on how it is wired.

REMOTE OPERATION

To operate the remote, disable the safety lock out by pushing both buttons for 2 seconds.

NOTE: After 1 minute of not pushing a button on the remote the safety lock out is activated.

MAINTENANCE  |  Safety Messages


Read entire sheet before operating this product.

The swing arms rotate under extreme spring tension. Before making any repairs, see repair instructions “Properly Releasing Spring Tension” and properly release spring tension.

Take care repairing systems with broken or damaged parts, including the tarp. Broken or damaged parts could come loose unexpectedly and allow the swing arms to freely rotate with tremendous force. Secure broken or damaged parts until tarp is fully unrolled and repairs can be made.

DO NOT operate when damaged.





NEVER allow anyone to stand in the path of the arms when arms/tarp is damaged. Arms/tarp could come loose allowing the swing arm to freely rotate.

Follow industry safety guidelines when making any repairs.

Broken or damaged parts could cause death or serious injury.


DO NOT repair arms/castings. Repaired arms/castings could fail.

DO NOT unlock the clamps holding the anchor pipe before releasing the spring tension on the AeroForce S2S. Unlocking the anchor pipe clamps can cause a rapid release of spring tension allowing arms to rotate with the anchor pipe and tarp coming off the trailer. Persons in the area could be hit with moving parts.

DO NOT unlock the clamps holding the anchor pipe.






Keep all clothing clear of moving parts.
Spring and arms are under extreme tension. DO NOT stand in the path of or on the arms.


Repairs must only be made after proper instruction.

Maintenance Recommendations

Aero Industries recommends a weekly inspection of the following items:


Replace all worn or broken parts immediately.
Repairs must ONLY be made after proper instruction.
  • Inspect Tarp for wear and tears.
  • Inspect Arms for damage (cracked, dented or bent).
  • Fasteners: Make sure that all mounting bolts and screws are in place and tight and that no parts are worn or damaged.
  • Bearings: Pull the shafts from side to side and in and out . If there is excessive play, replace the bearings. Lubricate as often as necessary with penetrating oil. DO NOT use an excessive amount of lubricant.
  • Chain: Check the chain tension, that links move smoothly, and make sure the master link is on. Lubricate the chain regularly with penetrating oil.
  • Electrical Connections: Check all the electrical connections and tighten any loose connections.
  • Safety Labels: Clean labels with soap and water. Replace if damaged and/or difficult to read.

Replacement parts and instructions may be obtained from your Aero dealer or by contacting Aero Industries.

LABELS & SYMBOLS  |  Aeroforce S2S Explanation

This Safety Label part #0920-039001 should be attached to the swing-arm near the springs. To receive a label or replace a damaged label contact Aero Industries Inc.

Explanation of Signal Words

Warning

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Caution

Indicates a hazardous situation which, if not avoided could result in minor or moderate injury.

Notice

Used to address practices not related to physical injury.